Skip to content
Every Mechanism

Home How a Toilet Works

No pump, no motor

How a toilet works

Gravity, the shape of the bowl and two clever valves. Press the handle and six litres of water empty the bowl in a few seconds, then the tank quietly fills itself up again.

Pour a bucket
6L
a full flush
3L
a small flush
1min
to refill the tank
0
pumps or motors
A toilet cut in half in the middle of a flush: the flapper is open in the tank and water fills the passages inside the china bowl.

Video

How a Toilet Works - The Siphon Inside the Bowl

Watch on YouTube

3D model · 360° · zoom

Press the handle

It is already cut in half. Press Flush and watch the flapper lift and float, the tank empty, the rim and the jet wash the bowl, the siphon pull it empty and the fill valve refill it all. Drag to turn it, scroll or pinch to zoom, and click a part to use it.

Try itPress Flush. The flush is shown in slow motion, and the refill sped up.
Loading the 3D model…

Meet the parts

Two pieces of china, a handful of parts

Here it is taken apart and cut in half. Tap any part of the picture or pick a name below. The bowl is at the bottom, the seat above it, then the tank with both valves inside it, and the lid on top.

The toilet taken apart and cut in half: the bowl with its trap at the bottom, the seat above it, the tank lifted off the bowl with the flush valve, flapper, overflow tube and fill valve inside it, and the lid on top.

Hover or tap the picture. Orange rings mark every part.

Parts diagram

Follow the water

Cut down the middle and seen from the side, with the front of the toilet on the left. The numbers follow the water: 1 to 4 bring it into the tank, 5 to 11 let it out, and 12 to 19 carry it through the bowl to the drain.

The toilet cut in half and seen from the side, with nineteen numbered parts from the supply line to the drain.
    How it works, step by step

    Nineteen steps, one flush

    The same steps as the video. Each picture is a moment from it; press Show me in 3D to set the model up for that step.

      A two-piece toilet: the tank sits on the back of the china bowl.
      Step 1 of 19

      No pump, no motor

        Demo · the siphon

        Pour it in fast

        You can flush a toilet with no tank at all: tip a bucket of water into the bowl, quickly. Pour slowly and nothing happens. Why?

        The water in the bowl can only rise to the top of the bend in the trap; anything more spills over the bend and trickles away. Pour fast and the spill fills the whole downward pipe. A pipe full of falling water is a siphon: it pulls the rest of the bowl after it, faster than you poured, until air gets in and breaks it with a gurgle.

        • Slowly: it just spills over the bend, as fast as you pour.
        • Quickly: the down pipe fills, and the siphon empties the bowl.
        0water over the top of the bend, mm
        0.00spilling over the bend, L/s
        Offsiphon
        0.0poured in, litres

        Demo · one flush

        One flush, second by second

        The tank empties in about two seconds and the siphon takes about one and a half more to clear the bowl. Then the refill takes a minute. Play it, or drag along the time line: the first six seconds are stretched out so you can see them.

        6.0in the tank, litres
        0.0let out, litres
        –the siphon ran, seconds
        –full again after, seconds

        Dual flush at home

        A small flush lets the flapper drop early, with half the tank still in it: about three litres, plenty for liquids. How much does that save in a day?

        Demo · what goes wrong

        Why a toilet keeps running

        Most toilet trouble is in the tank, and most of it wastes water quietly. Pick a fault and watch where the water goes.

        Water that slips past the flapper, or runs down the overflow tube, goes straight through the bowl to the drain, and the fill valve keeps replacing it. A chain that is too long has the opposite problem: the flush is too weak to start the siphon.

        • Leaks waste water all day and all night.
        • Hold to flush keeps the handle down for as long as you press.
        0wasted, litres a day
        0.0into the bowl now, L/min
        Shutfill valve
        Shutflapper

        More to know

        Kinds, history and care

        Six ways to flush

        Siphon jetThe one on this page. A jet of water starts a siphon in the trap, and the siphon pulls the bowl empty. Common in North America.
        WashdownNo siphon: the rush of water from the rim simply pushes everything over a short, wide trap. Common in Europe and Australia.
        Dual flushTwo buttons, a small flush and a full one. Most use a drop valve lifted by the buttons; this one lets its flapper drop early.
        Pressure assistedA sealed tank inside the cistern uses the mains pressure to squeeze air. Opened, it fires the water out in a powerful blast.
        Hidden cisternThe tank is built into the wall with a push plate on the front, and the bowl hangs on a steel frame clear of the floor.
        VacuumIn planes, trains and ships. A valve opens to a pipe at low pressure, and the air rushes everything away with a splash of water.

        From a cistern to six litres

        1. Sir John Harington describes a flushing toilet with a cistern and a valve in his book The Metamorphosis of Ajax.
        2. Alexander Cumming, a Scottish watchmaker, patents a toilet with an S-shaped bend that holds water to keep the smells out.
        3. Joseph Bramah patents a better one, with a hinged flap at the bottom of the bowl and a float valve to refill it.
        4. Toilets made in one piece of glazed china appear, such as Thomas Twyford’s “Unitas”.
        5. The plastic float-cup fill valve, like the one on this page, starts to replace the old ball float on a long arm.
        6. In Australia, Caroma brings out a two-button dual-flush toilet.
        7. New toilets in the United States are limited to 1.6 US gallons, about six litres, a flush.
        8. Efficient toilets flush with 4 to 4.8 litres, and dual-flush ones with about three for a small flush.

        Keeping one happy

        • Test for a leaky flapper: put a few drops of food colouring in the tank and don’t flush. If colour shows in the bowl after 15 minutes, the flapper leaks.
        • Leave the chain a little slack, about a centimetre, with the handle at rest. Tight, it holds the flapper open; too loose, the handle can’t lift it.
        • Set the water level to the mark on the overflow tube, a few centimetres below its top. Any higher and water runs away down the tube.
        • Never flush wipes, even “flushable” ones. They don’t break up like paper, and they snag in the trap and the drains.
        • A weak flush can mean scale in the rim holes or the siphon jet. Hard water leaves lime; vinegar and a small brush clear it.
        • Before working in the tank, turn the stop valve off and flush, so the tank is empty and stays empty.

        Things worth knowing

        A bucket does the jobPour about six litres in quickly and the bowl flushes, tank or no tank. It is the speed, not the tank, that starts the siphon.
        The gurgleThat sound at the end of a flush is air rushing into the trap and breaking the siphon.
        It floats openThe flapper is hollow underneath. Once it is lifted, the trapped air holds it up until the tank is nearly empty.
        A seal of waterThe trap always keeps a plug of water in its bend: seven centimetres deep in this one, enough to stop the sewer gas.
        Half the old amountToilets used to take 13 litres or more a flush. This one takes six, and its small flush three.
        Clean waterIn most homes the water in the tank comes straight from the mains, the same water as in the kitchen tap.
        Quick check

        Four questions